an fitting size chart id

AN sizes are mesured by 16ths of an inch. FREE SHIPPING on orders over 99.

Garage Door Header Size Chart Check More At Http Dragonmonster Design Garage Door Header Size Chart Garage Doors Standard Garage Door Sizes Garage Door Sizes

In Pilot Length in Bead OD.

. 316 38 - 24 SAE-4 AN. Whereas the AN is preceded by a - and two digits single digit sizes should have a 0 in front. For example a -3 AN hose has an external diameter of 316th of an inch.

Both of these terms refer to the same union type. Brass Fitting Identification Chart. Quick Reference Guide for finding -AN size in reference to thread size.

Technical Data 150 PSI Threaded Stainless Steel Fittings. 316 013 012 716-20. Inside diameter of the hose is designed to match up to an equivalent hard line ID.

For every 16th of an inch you have one size of AN. Is a universal abbreviation for sizing pipe systems. The most common uses of AN hoses on race cars.

The following charts will show a Dash number for each fitting. Similarly -8 AN hoses are 816 12 inch in outer diameter. Use the diagram below to find pipe thread size.

Armed forces A for army and N for navy describe the outside diameter OD of tubing in 116-inch increments. The numbers assigned equal the size in 116 inch increments. -4 AN 416 or 14.

For example an -8 AN fitting translates to an 816 inches or 12-inch. AN fittings are a flare fitting using 37 flared tubing to form a metal-metal seal. Fitting thread size chart is intended as a quick reference guide for thread size by dash size.

116 Dash Size in. Dimensions to ANSI 163. The nominal outside diameter of the tubing is expressed in sixteenths of an inch increments and then given an equivalent dash number.

12 rows MALE ANORB ADAPTER IDENTIFICATION CHART. 65 rows AN sizes originally developed for use by the US. 14 022 017 916-18.

A 38 port would be 616 or a Dash 6 -6. SAE J1453 ORFS O-ring Face Seal connections are considered the best for leak control. Therefore a -8 AN size would be equal to 12 OD tube 8 116 12.

Plastic Thread Cap and Plug Sizing Chart. -6 AN fuel or coolant hoses. 12 044 039 78-14.

14 716 - 20 SAE-5 AN. You can convert any AN fitting to its nominal inch size by dividing the AN number by 16 as follows. So measure out your radiator fitings and convert it in to basic 16ths and youll have it.

Thread Size Chart for AN Fittings. Tightening. -4 AN fuel hoses.

For some odd reason the automotive industry wants to make AN fittings sound like something special. 14 line is 4 16ths of an inch so it is an AN 4. The table below shows which AN size matches which JIC size.

AN8 816 or 12 for example. Inch size Dash size Long pilot Short pilot Bead OD. Place fitting against base line.

Read fitting size where it intersects the vertical line. In Pilot Length in 3 8-6 052 028 052 019 1 2-8 064 039 064 019 5 8-10 077 039 077 019 3 4-12 091 039 091 019. The Dash number comes from the dimension of the port of the fitting.

However this system does not specify the ID inside diameter of the tubing because the tube wall can vary in thickness. -02 -03 -04 -05 -08 and -10 of SAE 37 and SAE 45 have the same threads but NOT the same seat angles. -8 AN a very common size for coolant and oil.

MALE AN ADAPTER IDENTIFICATION CHART. 516 12 - 20 SAE. Pressure to ANSI 165 Class 150LB- Material ASTM A351 CF8 AISI304 or ASTM A351 CF8M AISI316.

Each AN size also uses its own standard thread size. Thread Dash for JIC 37 Flared Series 23 24 P23 P12 P24 P25 26 Connectors. It is the dimension in 116 of an inch.

Keeping this in view what size is an fitting. Free Shipping on orders over 99. The line drawings below depict.

Please Register or. The male connector has a straight thread and an O-ring in. Of 816 or 12.

38 034 030 34-16. Where every dash number is 116 of an inch an AN6 fitting would be equivalent to 616 or 38 Fitting size. 58 056 048 1 116.

-3 AN fittings used for brake lines. Male Thread Size AN Size Equivalent Tube Size Nominal OD Hose ID Male fitting ID. 116 Dash Size 18 216 -2 1 1616 -16.

Intermixing the two different types of fittings will result in leakage so use care in measuring seat angles. Click to see full answer. Each AN size refers to the outer diameter od of the tube or inner diameter id of the hose that its used with.

Of 216 or 18 while an AN 8 fitting will fit a tube with an OD. For example an AN 2 fitting will fit a tube with an OD. My Account Need Help.

The similarities end with the fittings and the ID. Use this handy chart to determine the -AN fitting size based on corresponding thread sizes. 15 rows Hose Size Chart Fractional Equivalent All dimensions are in inches unless otherwise noted.

Below weve compiled a hydraulic hose fittings chart describing some of the more common fitting sizes and types currently in use by pipefitters and other professionals. JIC fittings size chart for identifying the correct size of bulkhead fitting adapter for skid steer quick couplers. 12 line is 8 16ths of an inch so it is an AN 8.

We also show the actual UNF thread used on these fittings and how this will read in a digital vernier gauge.

Sae J2552 Male Standpipe Push On Hose Fittings Sae J846 8501a8 Dimension Sae Hose Push